Pool Surface Area Calculator

Find the total interior surface area of your pool, floor and walls together. Handy for pool paint, plaster, liners and coatings.

1. Choose Your Pool Shape
2. Enter Your Measurements
Flat floor? Enter the same number in both boxes, or leave the maximum empty. For a sloped floor we use the average of the two depths.
Most jobs need a little more than the exact area. Enter 0 if you want the exact figure only.

Estimates only. Surface area is the floor plus the walls, using your measurements and the average depth. Irregular shapes, steps, benches and slopes can change the real figure, so always check your plan before you buy materials.

Pool Surface Area Calculator: How Much Surface Does Your Pool Really Have?

If you are planning to repaint, replaster or retile your pool, the first thing any supplier asks is how many square feet you have. Guess too low and you run out halfway through the job. Guess too high and you pay for material you never use. This calculator measures the whole inside of your pool, floor and walls together, so you can order with confidence.

How it works

A pool’s surface is not just the floor. The walls count too, and on a deep pool they add up fast. The calculator does two things. First, it finds the floor area for your shape. Second, it works out the distance around the pool and multiplies it by the average depth to get the wall area. Add the two and you have your total. It then adds an allowance for waste, so you know how much to actually order.

For a sloped floor, the average depth is the shallow end plus the deep end, divided by 2.

The shapes we support

  • Rectangle: length times width.
  • Round: pi times the radius squared.
  • Oval: the true ellipse formula, which is about 0.785 times length times width.
  • Lazy L: the full outside rectangle, minus the corner that is missing.
  • Roman: a rectangle with one or both ends rounded by the corner radius you enter.
  • Kidney bean: the standard industry formula, 0.45 times both lobe widths added together, times the length.

A worked example

Take a pool 50 feet long and 20 feet wide, with a 3 foot shallow end and a 7 foot deep end.

The floor is 50 times 20, which is 1,000 sq ft. The average depth is 5 feet. The distance around the pool is 140 feet, so the walls are 140 times 5, which is 700 sq ft. Your total surface area is 1,700 sq ft.

With 10 percent extra for waste, you would order for about 1,870 sq ft. If your paint covers 150 sq ft per gallon and you plan 2 coats, that works out to roughly 25 gallons. This is only an example, so always use the coverage printed on your own product label.

How to measure properly

  • Measure the inside of the pool, not the outside edge of the coping.
  • Take depth readings at the shallowest and deepest points of the floor, away from steps.
  • Use a long tape and a helper so the line stays straight, and measure twice.
  • If your pool has steps, benches or a tanning ledge, measure those separately and add them to the result.

Why we add extra

Real jobs always use more than the exact area. You lose some to cutting, overlap and spills, and rough plaster or old concrete soaks up more coating than smooth surfaces. We start you at 10 percent extra. You can change it, and a good supplier will tell you what they recommend for your material.

Frequently asked questions

Does pool surface area include the walls?

Yes. For painting, plastering, tiling or any resurfacing job, you need the floor and the walls. That is why this calculator gives you both.

What is the difference between surface area and volume?

Surface area is the material you cover, measured in square feet. Volume is the water the pool holds, measured in gallons. We show both, but use surface area when you buy coatings and volume when you buy chemicals.

Liked this one? Check out all our free calculators here.

How much extra should I order?


Around 10 percent is a sensible starting point for most jobs. Go higher for rough surfaces, complex shapes or if you are a first time painter.

Do steps and benches count?

Not automatically. Measure them separately and add that area to your total, since they add both flat surface and extra edges.

Can I use this for a vinyl liner?

Use it as a rough guide only. Liners are cut to a pattern for your exact pool, so rely on a measured quote from the liner supplier.

Why does my oval result differ from a quick rule of thumb?

Some quick rules use a multiplier near 0.89 for ovals with fuller, straighter sides. We use the true ellipse formula. A very boxy oval may measure slightly larger in real life, and the extra allowance covers that

Disclaimer

This calculator provides estimates only. Real pools can have steps, benches, slopes and curves that change the true surface area, so please measure carefully and check with your supplier before you buy materials. Coverage and waste vary by product and surface condition.